Are you currently hunting for facts and techniques concerning A Step-by-Step Guide to Installing a Bathtub?
Setting up a bath tub isn't precisely brain surgery, yet it does call for strong plumbing, carpentry, and in some cases, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably difficult job. If the old bathtub is conveniently accessible, the job can move easily; if you have to open a wall surface to remove the old tub as well as place the new tub, the task is much harder. In either instance, the task is within a home handyman's abilities, although you will certainly require a helper to move out the old tub and also set in the brand-new one. See to it you have certified on your own for the job and also are comfortable attempting it. Rather than employing a specialist to take control of a halfway-completed job, it is far better to think about using one before you start. Possibilities are you might need an expert plumber to make tube links.
This short article will certainly help you set up a brand-new tub in your washroom if you have currently acquired a new bathtub and also don't require to transform the setup of your previous water pipes.
Your devices as well as product checklist need to comprise the following:
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you should do is detach the water. After doing so, turn on the faucets to drain pipes any type of water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the restricted gain access to that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the taps. Have a towel ready for the continuing to be water that will come from the pipelines. As soon as the supply pipes have actually been removed, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly call for minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin making certain that the washers are in location in between the tap and the sink. Protect the faucet in position with the manufacturer supplied backnut. Once the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet connectors. The former type ought to be linked to the faucet finishes first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Installing the Tub
Using the two wooden boards under its feet, position the bathtub in the required position. The wooden boards are valuable in equally spreading out the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four small points.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the tub up until the level checks out level.
To install faucets, fit all-time low of the outermost adaptable faucet port to the proper supply pipeline by making a compression sign up with; then do the exact same for the other tap.
Switch on the supply of water and check all joints and brand-new pipework for leakages and also tighten them if needed. Fill up the bathtub and also check the overflow outlet and the regular electrical outlet for leakages.
Lastly, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub needs to wait till the bath tub has actually been made use of at the very least when as this will certainly resolve it into its final position.
Preparing for the Installation
Firstly, the sustaining structure provided with the bathroom ought to be fitted (if called for) according to the supplier's guidelines. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to make sure that if the tap features a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
Fit the versatile tap connectors to the bottom of both faucets making use of 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you use every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be suited its last position.
Tiling Around the Bath tub
In the area where the bathroom satisfies the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the installation can move enough to split an inflexible seal, triggering the water to penetrate the wall between the bathroom and the tiling, causing difficulties with dampness as well as feasible leaks to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your fixtures as well as fittings. They are offered in tubes and also cartridges, and also can sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water prior to sealing, to enable the motion experienced when the bathtub remains in use. The sealant can split rather very early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise quickly offered on the marketplace. It is suggested to fit the tiles using water-resistant or water resistant sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a keen person who reads about How to Install a Bathtub, I figured sharing that piece of content was smart. Liked our piece of writing? Please share it. Help someone else locate it. Many thanks for taking the time to read it.
Book Today!